Grove - Slide Potentiometer


3.3V 5.0V Analog

The Grove - Slide Potentiometer module incorporates a linear variable resistor with a maximum resistance of 10KΩ. When you move the slider from one side to the other, its output voltage will range from 0 V to the Vcc you apply. It connects to the other Grove modules through a standard 4-Pin Grove Cable. Three of the pins are connected to OUT (Pin 1), Vcc (Pin 3) and GND (Pin 4), while the fourth pin (Pin 2) is connected to a on-board green indicator LED. The LED is used to visually represent the resistance change on the potentiometer.


  • 30 mm long slide length
  • Linear resistance taper
  • Grove compatible


More details about Grove modules please refer to Grove System

Application Ideas

Here are some projects for your reference.

Arduino BoomBox Arduino BeatBox
Make it NOW! Make it NOW!


Item Min Typical Max
Voltage (DC) 3.3V 5.0V 30V
Current - - 30mA
Dimension 24mm x60mm
Net Weight 8.6g
Rotational life >15,000 cycles
Total resistance 10KΩ
Stroke length 30mm
Total resistance tolerance +/- 20%

Platforms Supported

Getting Started

As an Adjustable Resistor

As shown below, the Grove - Slide Potentiometer can be used as a simple slide potentiometer in any MCU controlled or stand-alone project.


Follow these steps to build a sample Grove circuit using this module but without using any microcontroller board:

  1. Connect the slide potentiometer module to the input side of your circuit (to the left of the power module). On the output side of the circuit, you may use a range of User Interface modules (Grove - Red LED, Grove - LED String Light, Grove - Mini Fan, Grove - Buzzer, Grove - Recorder etc.)
  2. Power up the circuit when complete.
  3. The slide potentiometer module can now be used to trigger an output. For example:

    • When used in conjunction with a Grove - Red LED output module, observe that the brightness of the LED increases as you move the slider from GND to Vcc. At Vcc, the resistance of the potentiometer is minimum and the LED burns the brightest. The same behavior can be seen when the slide potentiometer is used with the Grove - LED String Light module - the more voltage you apply by taking the slider towards the Vcc mark, the brighter the LED lights would become.
    • Similarly, you can use the slide potentiometer to vary the speed of your Grove - Mini Fan or the frequency with which your Grove - Buzzer module sounds
    • The slide potentiometer can also be used as an ON/OFF switch for any circuit. Take the slider to the Vcc position to switch it ON and move it down to GND to switch OFF a circuit.

In terms of choosing a power module, you can use either the Grove - USB Power module or the Grove - DC Jack Power module for building standalone Grove circuits.

With Arduino

As a Voltage Divider

Follow these simple steps to make the slide potentiometer module function as a voltage divider:

1.When using the module in conjunction with an Arduino or a Seeeduino, use the Grove - Base Shield and connect the Grove - Slide Potentiometer module to the shield using a designated Grove Interface (e.g. Analog Port 0 as shown below).

2.Connect the board to PC using USB cable.

3.Upload the following sample sketch.

int adcPin = A0; // select the input pin for the potentiometer
int ledPin = A1; // select the pin for the LED
int adcIn = 0;   // variable to store the value coming from the sensor
void setup()
    Serial.begin(9600); // init serial to 9600b/s
    pinMode(ledPin, OUTPUT); // set ledPin to OUTPUT
    Serial.println("Sliding Potentiometer Test Code!!");
void loop()
    // read the value from the sensor:
    adcIn = analogRead(adcPin);
    if(adcIn >= 500) digitalWrite(ledPin,HIGH);  // if adc in > 500, led light
    else digitalWrite(ledPin, LOW);

4.Open the serial monitor. You should see some data from ADC.

5.Move the lever back and forth. The serial data will change correspondingly. When the output resistance exceeds a certain preset value, the on-board indicator LED will also light up.

As an HID Device

Slide Potentiometer can be an effective Human Interface Device (HID) and can be used, for example, in the radio controller of a Radio Controlled toy car. The picture below shows two Slide Potentiometers on the control panel - one to control the speed of the left wheel, and the other to control the speed of the right wheel of the toy car respectively. Now you can change the speeds of both motors and see the behavior. You will see that if you make the right wheel spin faster than the left wheel, the car will turn rightwards, and if you make the left wheel spin faster than the right wheel, the car will turn leftwards.

With Raspberry Pi

1.You should have got a raspberry pi and a grovepi or grovepi+.

2.You should have completed configuring the development enviroment, otherwise follow here.


  • Plug the sensor to grovepi socket A0 by using a grove cable.

4.Navigate to the demos’ directory:

    cd yourpath/GrovePi/Software/Python/
  • To see the code
    nano   # "Ctrl+x" to exit #
import time
import grovepi

# Connect the Grove Slide Potentiometer to analog port A0
slide = 0   # pin 1 (yellow wire)

# The device has an onboard LED accessible as pin 2 on port A0
led = 1     # pin 2 (white wire)


while True:
        # Read sensor value from potentiometer
        sensor_value = grovepi.analogRead(slide)

        # Illuminate onboard LED
        if sensor_value > 500:

        print "sensor_value =", sensor_value

    except IOError:
        print "Error"

5.Run the demo.

sudo python


ArduinoWioBeagleBoneRaspberry PiLinkIt ONE


The platforms mentioned above as supported is/are an indication of the module's hardware or theoritical compatibility. We only provide software library or code examples for Arduino platform in most cases. It is not possible to provide software library / demo code for all possible MCU platforms. Hence, users have to write their own software library.

Help us make it better

Thank you for choosing Seeed. A couple of months ago we initiated a project to improve our documentation system. What you are looking at now is the first edition of the new documentation system. Comparing to the old one, here is the progresses that we made:

  • Replaced the old documentation system with a new one that was developed from Mkdocs, a more widely used and cooler tool to develop documentation system.
  • Integrated the documentation system with our official website, now you can go to Bazaar and other section like Forum and Community more conveniently.
  • Reviewed and rewrote documents for hundreds of products for the system’s first edition, and will continue migrate documents from old wiki to the new one.

An easy-to-use instruction is as important as the product itself. We are expecting this new system will improve your experience when using Seeed’s products. However since this is the first edition, there are still many things need to improve, if you have any suggestions or findings, you are most welcome to submit the amended version as our contributor or give us suggestions in the survey below, Please don’t forget to leave your email address so that we can reply.

Happy hacking