Grove - Speech Recognizer

Introduction

enter image description here

Use voice to interact with things around you can always be one of the most interesting things of IoT application, we want to make something more different and cooler. Recently we just launched the voice control solution “Respeaker” on Kickstarter and it becomes the blockbuster. However not everybody needs a Respeaker to build voice control project, sometimes people only need a simple solution, here we would like to introduce the first generation of grove speech recognizer to realize your dream of smart home easily and fast.

Grove speech recognizer is a designed for voice control application such as smart home, smart toy, voice control robot, anything you would like to control through voice, it worth a try. The board includes a Nuvoton ISD9160, a microphone, 1 SPI flash, 1 grove connector,1 speaker connector and 1 led to reflect to your voice.

Nuvoton ISD9160 is (SoC) Chipcorder that based on Cortex™-M0, it provides strong and economic solution for voice control applications. ISD9160 is not the only amazing thing in this grove. Let’s look at the microphone. Remember the uncomfortable moment when you have to speak directly and closely to the voice recognizer device to make sure it can hear you? It won’t happen this time! The microphone on grove-speech recognizer is Omni-directional, which means that whether a user speaks into the microphone from the front, back, left or right side, the microphone will record the signals all with equal gain.

This speech recognizer can recognize 22 pieces of commands including ‘start’, ‘stop’, ‘Play music’ and so on. Every time it recognizes a command, it will return a value and then the loudspeaker that connected to it will repeat the command. This value can be used to control other devices like motor, music player. We have tested it for hours to make sure it possesses a high recognition rate and a very low false trigger.

Here are some notes that you must know before using it: Awaken Word: Hicell (Please pronounce it as one word) When it recognizes the awaken word, LED turn red, then you can say the command word, if it recognize the command word, LED will turn blue.

Note

The firmware of the module was wrote by the third party vendor, it’s not open source.

Application Ideas

  • Internet of Things
  • Smart House
  • Human Machine Interface
  • Lighting Control
  • Sensor Hub
  • Robot

Features

  • Local Voice Recognition
  • Very low rate of false triggering
  • Speaker connector(JST2.0, speaker is not include)
  • Built-in microphone
  • 3.3/5V working voltage
  • 22 recognition entry
  • Default Baudrate: 9600

Tip

More details about Grove modules please refer to Grove System

Platform Support

Arduino Wio BeagleBone Raspberry Pi LinkIt
enter image description here enter image description here enter image description here enter image description here enter image description here

Specification

Item Min Typ Max Condition
Operating Voltage 3V 3.3V 5V 25 ℃
Operating Current 25mA 26.5mA 80mA@playing VCC = 3.3V 25℃
Operating Current 25mA 26.5mA 130mA@playing VCC = 5V 25℃
Operating Temperature 0℃ 25℃ 85℃
Size 40*20mm
Weigth 5g
Flash 2Mbytes
Microphone Sensitivity -43dB -40dB -37dB VCC = 5V 25℃
Microphone SNR 58dB
Microphone Directivity Omni-directional
Speaker Power 1W VCC = 5V 25℃
Processor core Cortex-M0
Processor Frequency 32.768MHz 50MHz VCC = 5V 25℃

Hardware Overview

enter image description here

  1. Grove Connector
  2. Red Led - lights when “HIcell” is recognized
  3. Blue Led - lights when a command is recognized
  4. Speaker Connector - You can connect a speaker to get the voice return
  5. Microphone
  6. ISD9160CFI - controller

Command Return

Command Value
Turn on the light 1
Turn off the light 2
Play music 3
Pause 4
Next 5
Previous 6
Up 7
Down 8
Turn on the TV 9
Turn off the TV 10
Increase temperature 11
Decrease temperature 12
What’s the time 13
Open the door 14
Close the door 15
Left 16
Right 17
Stop 18
Start 19
Mode 1 20
Mode 2 21
Go 22

Getting Started

Here we will show you how this Grove - Speech Recognizer works via a simple demo. First of all, you need to prepare the below stuffs:

Seeeduino V4 Grove - Speech Recognizer Base Shield
enter image description here enter image description here enter image description here
Get ONE Now Get ONE Now Get ONE Now

Hardware Connection

Thanks to the benefit of Grove series module, you don’t need to make soldering or bread board, what you need to do is connect the modules to the right port of Base Shield. For this demo, we connect Grove - Speech Recognizer to D2.

enter image description here

Software

Copy the below code and paste to your Arduino IDE, and upload to your Seeeduino V4. After upload the code to an Arduino, let open the Serial monitor.

#include <SoftwareSerial.h>

#define SOFTSERIAL_RX_PIN  2
#define SOFTSERIAL_TX_PIN  3

SoftwareSerial softSerial(SOFTSERIAL_RX_PIN,SOFTSERIAL_TX_PIN);

const char *voiceBuffer[] =
{
    "Turn on the light",
    "Turn off the light",
    "Play music",
    "Pause",
    "Next",
    "Previous",
    "Up",
    "Down",
    "Turn on the TV",
    "Turn off the TV",
    "Increase temperature",
    "Decrease temperature",
    "What's the time",
    "Open the door",
    "Close the door",
    "Left",
    "Right",
    "Stop",
    "Start",
    "Mode 1",
    "Mode 2",
    "Go",
};

void setup()
{
    Serial.begin(9600);
    softSerial.begin(9600);
    softSerial.listen();
}

void loop()
{
    char cmd;

    if(softSerial.available())
    {
        cmd = softSerial.read();
        Serial.println(voiceBuffer[cmd - 1]);
    }
}

Awake the module

The module will wake up when there’s command Hicell, then the red led will on. Try again when the red led is not on.

Note

The red led will last 5 seconds. If the red led turn off before the command was recognized, you should Hicell again.

Command

After the module is awake, you can speak out the command. Such as

"Turn on the TV"

If the blue led is light(last about 1s), that means the command was recognized correctly. Take a look at your Serial monitor, the command was printed on it.

enter image description here

Resources

Help us make it better

Thank you for choosing Seeed. A couple of months ago we initiated a project to improve our documentation system. What you are looking at now is the first edition of the new documentation system. Comparing to the old one, here is the progresses that we made:

  • Replaced the old documentation system with a new one that was developed from Mkdocs, a more widely used and cooler tool to develop documentation system.
  • Integrated the documentation system with our official website, now you can go to Bazaar and other section like Forum and Community more conveniently.
  • Reviewed and rewrote documents for hundreds of products for the system’s first edition, and will continue migrate documents from old wiki to the new one.

An easy-to-use instruction is as important as the product itself. We are expecting this new system will improve your experience when using Seeed’s products. However since this is the first edition, there are still many things need to improve, if you have any suggestions or findings, you are most welcome to submit the amended version as our contributor or give us suggestions in the survey below, Please don’t forget to leave your email address so that we can reply.

Happy hacking